GenII AO REM Analogue Output Module Product Details

Home > Products > Product Search > Product Details > GenII AO REM Analogue Output Module

GenII AO REM Analogue Output Module

Digital / Remote Expansion Modules

This product has been discontinued.

Do you need help finding a replacement product? Contact Us
Email: sales@innotech.com
Phone: +61 7 3421 9100

The Innotech GenII AO REM Analogue Output Module is an expansion device for the Genesis range of Digital Controllers.

The module is powered by 24VAC and provides 5 analogue outputs to be connected to field equipment. Jumpers on the board allow either 0-10V or heat valve (PWM) style outputs to be selected for each channel.

The GenII AO REM may be located remotely from the Genesis Digital Controller and providing distributed analogue outputs for the system.

The GenII AO REM is configured and programmed via the Genesis Digital Controller.

The GenII AO REM communicates with the Genesis Controller via the REM Comms port. The remote link uses RS-485 at a baud rate of 38400. For pre-Version 5 controllers, a Gen II RMI Remote Module Interface is required. Please refer to DS15.01 for further information.

(Larger image)

Download Datasheet Contact Us

FeaturesApplicationsApprovals & ListingsTech SpecsDownloadsHow To Buy

5 Analogue Outputs.
Each output is configurable as 0-10V or heat valve (PWM).
Remote ouput of analogue control voltage points up to 500 mtrs from the Genesis Controller.
Housed in a low profile din rail mounted enclosure.
RS485 interconnection between REM Modules.
Galvanic Isolation for communications to prevent grounding problems.
24V AC operation.
JUMPER selectable Address.
Wiring Diagrams for modules generated by GEN2Config Software.
LED indication of network traffic to assist in network setup and debugging.

Application Notes

A Genesis Controller must have version 4 firmware installed to support REM Modules.

A Genesis Digital Controller can have up to 15 GENII AO REM Modules* connected to it via the REM comms bus.

For detailed connection information to the pre version 5 Genesis Digital Controller Family, please refer to the Innotech Cabling Manual (.pdf 1.54MB).

Applications

Expands Genesis Digital Controller I/O capabilities by providing 5 Analogue Outputs allowing distributed control via RS485.

	CE	https://europa.eu/youreurope/business/product/ce-mark/index_en.htm The CE label is a European marking for products to indicate conformity with the electromagnetic compatibility and health and safety requirements set out in European Union.
	FCC	https://www.fcc.gov FCC marking indicates that the product conforms with the regulations of the U.S. Federal Communications Commission (FCC) for microprocessor-based equipment.
	RCM	https://www.acma.gov.au The RCM compliance mark indicates that a device complies with applicable radiocommunication and electrical safety standards.
	UL	https://www.ul.com UL marking for USA and Canada indicates that the product conforms with the safety standards laid down by Underwriters Laboratories.

Power Supply

Voltage: 24 volts AC ±10% @ 50/60Hz.
Power Consumption: 4VA max.

The operating voltage must meet the requirements of Safety Extra Low Voltage (SELV) to EN60730. The transformer used must be a Class 2 safety transfomer that has the energy and voltage limiting characteritics as described in the National Electrical Code, ANSI/NFPA70. It must also be sized and fused in compliance with local safety regulations.

Outputs

Linear 0-10V, maximum load 2 mA
PWM 10Vpp, maximum load 2mA

Terminal Identification

1 = 24V AC Supply.
2 = 0V AC Supply.
3 = Earth.

NOTE - TERMINAL 3 is for the protection of the Comms circuitry and must be connected to a good electrical bonded Earth. This may be the Earth bus bar of the switchboard or the point that connects the chassis of the equipment the Module is in, to electrical Earth. This point should not be tied to terminal 2.

COMMS Connection

SHLD 1	=	Shield from incoming Comms Cable.
+	=	RS 485 (+) signal.
-	=	RS 485 (-) signal.
SHLD 2	=	Shield from outgoing Comms Cable.

I/O Terminal Connections

A = Output 1 +.
B = Output 1 -.
C = Output 2 +.
D = Output 2 -.
E = Output 3 +.
F = Output 3 -.
G = Output 4 +.
H = Output 4 -.
I = Output 5 +.
J = Output 5-.

Temperature Ratings

Storage 0 to 50°C non-condensing.
Operating 0 to 40°C non-condensing.

Enclosure & Mounting:
The Innotech MAXTime is housed in rectangular cases suitable for DIN Rail mounting. Their housing is moulded from flame retardant plastics recognised by UL as UL 94-V0.

Colour : Grey.
Dimensions: 75mm(L) X 155mm(W) X 57mm(H)