The humidity of the air measured by the number of grains of water vapor present in one cubic meter of air.
The sum of gauge and atmospheric pressure (psia).
The temperature measured on the Kelvin scale.
The lowest temperature theoretically attainable on the Kelvin scale (approximately 273.16° C).
In physics, the taking up of light, heat, or other energy by molecules. The absorbed energy is converted into heat. Absorption in chemistry is the taking up of one substance by another. For example, a gas such as oxygen may be absorbed, or dissolved, in water. In the HVAC industry heat energy is absorbed from the medium being cooled and transferred in the refrigerant.
A shell device installed in the suction line of a HVAC system to prevent liquids from entering the compressor.
A processed carbon used in filter driers and commonly used in air filters to clean the air.
HVAC term for compressor driven air conditioning.
A mechanical device for moving or controlling a mechanism or system.
A change in gas condition where no heat is added or removed except in the form of work.
HVAC term for distributing air through a system to precisely match the required amount.
In HVAC an IAQ control strategy to remove various airborne particulates and/or gases from the air. The three types of air cleaning most commonly used are particulate filtration, electrostatic precipitation, and gas sorption.
A device used to control temperature and humidity of the air.
In HVAC the control of the quality, quantity, and temperature-humidity of the air in an interior space.
HVAC term for an air distribution outlet, typically located in the ceiling, which mixes conditioned air with room air.
In HVAC the rate at which outside air replaces indoor air in a space. Expressed in one of two ways: the number of changes of outside air per unit of time - air changes per hour (ACH); or the rate at which a volume of outside air enters per unit of time - cubic feet per minute (CFM).
HVAC term for a fan-blower, heat transfer coil, and housing parts of a system.
In HVAC refers to equipment that includes a blower or fan, heating and/or cooling coils, and related equipment such as controls, condensate drain pans, and air filters. Does not include ductwork, registers or grilles, or boilers and chillers.
The unwanted entrance of air due to leakage, temperature difference, or wind.
Openings through or within walls, through floors and ceilings, and around chimney flues and plumbing chases, that permit air to move out of the conditioned spaces of the building.
HVAC term for air having a temperature of 68 degrees F (20 degrees C) and a relative humidity of 36%% at 14.7 psia.
Where both the condensing and evaporating mediums are air.
HVAC term for a valve, either manual or automatic, that is used to remove unwanted air from the highest point of a piping system.
Electrical current that reverses direction periodically.
The air external to a building or device.
The temperature surrounding an object.
A continuous signal for which the time varying feature (variable) of the signal is a representation of some other time varying quantity, i.e analogous to another time varying signal. It differs from a digital signal in that small fluctuations in the signal are meaningful.
American Society of Heating Refrigeration and Air Conditioning Engineers.
Is the pressure that the atmosphere exerts on us. At sea level this is 14.7 psig also written as 29.92 " Hg.
A condenser operated with water that is exposed to the atmosphere.
A pressure actuated metering device to regulate the flow of refrigerant into the evaporator according to the evaporator pressure.
The amount of heat energy that may be converted into useful energy from a fuel.
Refrigerants that are mixtures or blends of different refrigerants that are at the same ratio in vapor as well as in liquid state.
A zeotrope having a temperature glide sufficiently small that it is inconsequential.
A combination of different refrigerants to mask one with desirable refrigerant properties, an example of this is R-502 which is a mixture of 48.8% R-22 and 51.2% R-115.
The emf that opposes the normal flow of current in a circuit.
This is the refrigerant pressure in the low side of the system also called low side pressure or suction pressure.
BACnet is an ASHRAE building automation and control networking protocol, was designed specifically to meet the communication needs of building automation and control systems for applications such as heating, ventilating, and air-conditioning control, lighting control, access control, and fire detection systems and their associated equipment. The BACnet protocol provides mechanisms by which computerized building automation devices can exchange information, regardless of the particular building service they perform. As a result, the BACnet protocol may be used by head-end workstation, general-purpose direct digital controllers, and application specific or unitary controllers with equal effect.
When the both the inside and outside pressure of a container equal each other.
Used to measure atmospheric pressure.
Also called draft damper, is a device installed in a chimney to allow for the adjustment of dilution air.
An integration of digital, electronic, and/or pneumatic controls and devices to provide unattended and automatic operation of buildings systems. Systems may include HVAC, elevators, fire suppression, smoke control, security, lighting, and other subsystems.
A corrugated cylindrical container which moves with a pressure change.
The software, hardware, and services associated specifically with the intelligent (i.e., information and communication technology, or ICT-based) monitoring, management, and control of energy, as well as the enhancement of a building's efficiency of operations for commercial buildings.
A temperature regulating or indicating device which works on the principal that two dissimilar metals with unequal expansion rates, welded together and will bend as their temperature changes.
A low-temperature evaporator that uses a fan to force air rapidly over a evaporator surface.
A valve with a small opening which permits a minimum fluid flow when the valve is closed.
A mixture consisting of two or more single components.
In HVAC the device in an air conditioner that distributes the filtered air from the return duct over the coil/heat exchanger. This circulated air is cooled/heated and then sent through the supply duct, past dampers, and through supply diffusers to the living/working space.
A system for centralizing and optimizing the monitoring, operating, and managing of a building. Services may include heating, cooling, ventilation, lighting, security, and energy management.
A vessel or tank where heat produced from the combustion of fuels such as natural gas, fuel oil, or coal is used to generate hot water or steam for applications ranging from building space heating to electric power production or industrial process heat.
The pressure of the steam or water in a boiler as measured, usually expressed in pounds per square inch gauge (psig).
The heating capacity of a steam boiler expressed in BTU per hour (BTU/H), horsepower, or pounds of steam per hour.
A term used for the first stage compressor in a cascading system.
A generic term for liquefied and pressurized gas, ordinarily butane, propane, or a mixture of the two, contained in a cylinder for domestic use.
A salt water mixture commonly used as a secondary refrigerant.
The amount of heat required to raise the temperature of one pound of water one degree Fahrenheit, equal to 252 calories.
Ability of a circuit system to store electricity. The capacitance of a capacitor is measured in farads and is determined by the formula C = q/V, where q is the charge (in coulombs) on one of the conductors and V is the potential difference (in volts) between the conductors. The capacitance depends only on the thickness, area, and composition of the capacitor's dielectric.
A colourless, odourless non-combustible gas with the formula CO2 that is present in the atmosphere. It is formed by the combustion of carbon and carbon compounds (such as fossil fuels and biomass), by respiration, which is a slow combustion in animals and plants, and by the gradual oxidation of organic matter in the soil.
Air filter housing activated carbon.
A colourless, odourless but poisonous combustible gas with the formula CO. Carbon monoxide is produced in the incomplete combustion of carbon and carbon compounds such as fossil fuels (i.e. coal, petroleum) and their products (e.g. liquefied petroleum gas, gasoline), and biomass.
Arrangement in which two or more refrigerating systems are used in series.
Space below the flooring and above the suspended ceiling that accommodates the mechanical and electrical equipment and that is used as part of the air distribution system. The space is kept under negative pressure.
See Air Conditioner.
This is the same as an Air Handling Unit, but serves more than one area.
In HVAC a system where heat is supplied to areas of a building from a single appliance through a network of ducts or pipes.
Cloro-Floro Carbon
HVAC term for the amount of air, in cubic feet, that flows through a given space in one minute. 1 CFM equals approximately 2 litres per second (l/s).
The amount of refrigerant in a system.
To add a charge of refrigerant to a system.
A check valve is a mechanical device normally applied to a piping system which allows fluid to flow in only one direction.
A mechanical valve which provides a variable water flow to an air-conditioning chilled water coil.
A cooling system used to cool water or brine.
Any piping system where the internal fluids are sealed from their surroundings. Commonly referred to as glycol loops
Buildings constructed with more than one foundation type; e.g., basement/crawlspace or basement/slab-on-grade.
The process of burning; the oxidation of a material by applying heat, which unites oxygen with a material or fuel.
Air that provides the necessary oxygen for complete, clean combustion and maximum heating value.
Any wholly or partially enclosed space in which combustion takes place.
The gaseous by-products of the combustion of a fuel.
An instrument used to measure positive pressure.
A refrigeration component that make a pressure difference in the system which causes refrigerant to flow.
Compressor which uses a piss cylinder mechanism to provide pumping action.
Compressor which uses vanes, a mechanisms, or other rotating devices to provide pumping action.
A fluid formed when a gas is cooled .
Liquid or droplets which form when a gas or cooled below its dew point.
The changing of a gas or vapour to a liquid.
The heat rejection component of a system where the refrigerant is condensed from a vapour to liquid.
Heat exchanger that transfers heat to the surrounding air.
Heat exchanger that transfers heat to water.
The device in an air conditioner or heat pump through which the refrigerant is circulated and releases heat to the surroundings when a fan blows outside air over the coils. This will return the hot vapour that entered the coil into a hot liquid upon exiting the coil.
Comb-like device used to straighten the metal fins on condensers or evaporators.
A fan used to move air through air-cooled condenser.
A high efficiency furnace that also removes latent heat form the combustion products.
See head pressure
The temperature at which a substance will condense.
Part of a refrigerating mechanism which pumps vaporized refrigerant from the evaporator, compresses it, liquefies it in the condenser, and returns it to the metering device.
Air that has been heated, cooled, humidified, or dehumidified to maintain an interior space within the "comfort zone." (Sometimes referred to as "tempered" air.)
The interior space of a building that is heated or cooled.
Air handling system that provides a constant air flow while varying the temperature to meet heating and cooling needs.
The quantity of heat that a cooling appliance is capable of removing from a room in one hour.
A value used to estimate interior air cooling requirements (load) calculated as the number of degrees per day (over a specified period) that the daily average temperature is above 65 degrees Fahrenheit (or some other, specified base temperature). The daily average temperature is the mean of the maximum and minimum temperatures recorded for a specific location for a 24 hour period.
HVAC term for controls that vary airflow through an air outlet, inlet, or duct. A damper position may be immovable, manually adjustable or part of an automated control system.
An actuator which will drive a mechanical damper variably or 2 position.
A Deadband (sometimes called a neutral zone) is an area of a signal range or band where no action occurs (the system is dead). Deadband is used in voltage regulators and other controllers. The purpose is common, to prevent oscillation or repeated activation-deactivation cycles (called 'hunting' in proportional control systems).
A unit for measuring the extent that the outdoor daily average temperature (the mean of the maximum and minimum daily dry-bulb temperatures) falls below (in the case of heating, see Heating Degree Day), or falls above (in the case of cooling, see Cooling Degree Day) an assumed base temperature, normally taken as 65 degrees Fahrenheit, unless otherwise stated. One degree day is counted for each degree below (for heating) or above (in the case of cooling) the base, for each calendar day on which the temperature goes below or above the base.
The product of 1 hour, and usually the number of degrees Fahrenheit the hourly mean temperature is above a base point (usually 65 degrees Fahrenheit); used in roughly estimating or measuring the cooling load in cases where processes heat, heat from building occupants, and humidity are relatively unimportant compared to the dry-bulb temperature.
A device for reducing the level of humidity in a room or home.
Components of the ventilation system that distribute and return air to promote air circulation in the occupied space. As used in this document, supply air enters a space through a diffuser or vent and return air leaves a space through a grille.
Used to refer to more than one concept. It can refer to discrete-time signals that have a discrete number of levels, for example a sampled and quantified analog signal, or to the continuous-time waveform signals in a digital system, representing a bit-stream.
Direct digital control is the automated control of a condition or process by a digital computer. DDC is often used to control HVAC (heating, ventilating, and air conditioning) devices such as valves via microprocessors using software to perform the control logic. Such systems receive analog and digital inputs from the sensors and devices installed in the HVAC system and, according to the control logic, provide analog or digital outputs to control the HVAC system devices.
Refers to the more common refrigerant evaporator coil. The evaporator is in direct contact with the air stream, so the cooling coil of the airside loop is also the evaporator of the refrigeration loop. The term “direct” refers to the position of the evaporator with respect to the airside loop. This coil usually has a direct expansion valve connected to the coil distributor.
A type of water heater in which heated water is stored within the tank. Hot water is released from the top of the tank when a hot water faucet is turned. This water is replaced with cold water that flows into the tank and down to just above the bottom plate under which are the burners.
A column of burning combustion gases that are so hot and strong that the heat is lost up the chimney before it can be transferred to the house. A draft brings air to the fire to help keep it burning.
A door-like device located at the mouth of a fireplace chimney flue for controlling the direction and flow of the draft in the fireplace as well as the amount of oxygen that the fire receives.
A device built into or installed above a combustion appliance to assure the escape of combustion by-products, to prevent back-drafting of the appliance, or to neutralize the effects of the stack action of the chimney or vent on the operation of the appliance.
An air conditioning system that has two ducts, one is heated and the other is cooled, so that air of the correct temperature is provided by mixing varying amounts of air from each duct.
HVAC term for an axial flow fan mounted in a section of duct to move conditioned air.
The round or rectangular tube(s), generally constructed of sheet metal, fiberglass board, or a flexible plastic-and-wire composite, located within a wall, floor, and ceiling that distributes heated or cooled air in buildings.
A set of automated controls and software that will monitor and optimize the use of energy in commercial buildings. An energy management system can reduce waste by adjusting heating and cooling usage. A typical system will collect data from energy meters, analyze it and identify opportunities for greater efficiency.
Conditions other than indoor air contaminants that cause stress, comfort, and/or health problems (e.g., humidity extremes, drafts, lack of air circulation, noise, and over-crowding).
HVAC term for mechanical removal of air from a portion of a building (e.g., piece of equipment, room, or general area).
A device that removes contaminants, by mechanical filtration, from the fresh air stream before the air enters the living space. Filters can be installed as part of a heating/cooling system through which air flows for the purpose of removing particulates before or after the air enters the mechanical components.
HVAC term for a type of heating system in which heated air is blown by a fan through air channels or ducts to rooms.
A registered trademark for a chlorofluorocarbon (CFC) gas that is highly stable and that has been historically used as a refrigerant.
A network gateway is an internetworking system capable of joining together two networks that use different base protocols. A network gateway can be implemented completely in software, completely in hardware, or as a combination of both.
A form of thermal energy resulting from combustion, chemical reaction, friction, or movement of electricity. As a thermodynamic condition, heat, at a constant pressure, is equal to internal or intrinsic energy plus pressure times volume.
The heat that flows from the building interior, through the building envelope to the outside environment.
The ratio of fuel energy input as heat per unit of net work output; a measure of a power plant thermal efficiency, generally expressed as Btu per net kilowatt-hour.
The grilled opening into a room by which the amount of warm air from a furnace can be directed or controlled; may include a damper.
The quantity of heat necessary to raise the temperature of a specific mass of a substance by one degree.
The number of degrees per day that the daily average temperature (the mean of the maximum and minimum recorded temperatures) is below a base temperature, usually 65 degrees Fahrenheit, unless otherwise specified; used to determine indoor space heating requirements and heating system sizing. Total HDD is the cumulative total for the year/heating season. The higher the HDD for a location, the colder the daily average temperature(s).
The rate of heat flow required to maintain a specific indoor temperature; usually measured in Btu per hour.
High Efficiency Particulate Arrestor (filters).
A nationally recognized energy rating program that gives builders, mortgage lenders, secondary lending markets, homeowners, sellers, and buyers a precise evaluation of energy losing deficiencies in homes. Builders can use this system to gauge the energy quality in their home and also to have a star rating on their home to compare to other similarly built homes.
A heating unit where heat is distributed by means of convection or fans.
A device for increasing the humidity in a room or home.
A measure of the moisture content of air; may be expressed as absolute, mixing ratio, saturation deficit, relative, or specific.
HVAC (pronounced either "H-V-A-C" or "H-vak") is an initialism or acronym that stands for "heating, ventilating, and air conditioning". HVAC is sometimes referred to as climate control and is particularly important in the design of medium to large industrial and office buildings such as skyscrapers and in marine environments such as aquariums, where humidity and temperature must all be closely regulated whilst maintaining safe and healthy conditions within.
Indoor air pollution.
Indoor air quality.
The air the people breathe inside a built environment.
Particles and dust, fibres, mists, bio-aerosols, and gases or vapours.
Air leakage inward through cracks and interstices and through ceilings, floors, and walls of a space or building.
HVAC term for a type of heating appliance that performs more than one function, for example space and water heating.
LonTalk is a protocol optimized for control created by Echelon Corporation for networking devices over media such as twisted pair, powerlines, fiber optics, and RF. It is popular for the automation of various functions in industrial control, home automation, transportation, and buildings systems such as lighting and HVAC.
In HVAC a system designed to increase ventilation within a crawlspace, achieve higher air pressure in the crawlspace relative to air pressure in the soil beneath the crawlspace, or achieve lower air pressure in the crawlspace relative to air pressure in the living spaces, by use of a fan.
In HVAC the movement of outdoor air into a space through intentionally provided openings, such as windows and doors, or through non-powered ventilators or by infiltration.
Condition that exists when less air is supplied to a space than is exhausted from the space, so the air pressure within that space is less than that in surrounding areas. Under this condition, if an opening exists, air will flow from surrounding areas into the negatively pressurized space.
A network is a collection of computers or devices connected to each other. The network allows these computers or devices to communicate with each other and share resources and information.
A set of connectivity standards for industrial automation from the OPC Foundation. OPC added extensions to Microsoft's COM and DCOM object technology in order to provide a set of common interfaces for process control. OPC offers interoperability between gauges, databases, programmable logic controllers (PLCs), distributed control systems (DCSs) and remote terminal units (RTUs).
Chemicals that contain carbon. Volatile organic compounds vaporize at room temperature and pressure. They are found in many indoor sources, including many common household products and building materials.
Air taken from the external atmosphere and, therefore, not previously circulated through the system.
HVAC term for air brought into a building from the outdoors (often through the ventilation system) that has not been previously circulated through the system. Also known as "Make-Up Air".
A state of matter in which solid or liquid substances exist in the form of aggregated molecules or particles. Airborne particulate matter is typically in the size range of 0.01 to 100 micrometers.
Fine liquid or solid particles such as dust, smoke, mist, fumes, and fog found in air and emissions.
HVAC term for an air compartment connected to a duct or ducts.
Condition that exists when more air is supplied to a space than is exhausted, so the air pressure within that space is greater than that in surrounding areas. Under this condition, if an opening exists, air will flow from the positively pressurized space into surrounding areas.
In flowing air, the total pressure minus velocity pressure. The portion of the pressure that pushes equally in all directions.
In flowing air, the sum of the static pressure and the velocity pressure.
In flowing air, the pressure due to the velocity and density of the air.
Regular and systematic inspection, cleaning, and replacement of worn parts, materials, and systems. Preventive maintenance helps to prevent parts, material, and systems failure by ensuring that parts, materials and systems are in good working order.
A type of thermostat that allows the user to program into the devices' memory a pre-set schedule of times (when certain temperatures occur) to turn on HVAC equipment.
A hydrocarbon gas, C3H8, occurring in crude oil, natural gas, and refinery cracking gas. It is used as a fuel, a solvent, and a refrigerant. Propane liquefies under pressure and is the major component of liquefied petroleum gas (LPG).
Two quantities are said to be proportional if they vary in such a way that one of the quantities is a constant multiple of the other, or equivalently if they have a constant ratio. Proportion also refers to the equality of two ratios.
The change in input required to produce a full range of change in the output due to the proportional control action. Or simply, it is the percent change of the input signal required to change the output signal from 0% to 100%.
A proportional–integral–derivative controller (PID controller) is a generic control loop feedback mechanism (controller) widely used in industrial control systems. A PID controller attempts to correct the error between a measured process variable and a desired setpoint by calculating and then outputting a corrective action that can adjust the process accordingly and rapidly, to keep the error minimal.
A communications protocol is the set of standard rules for data representation, signaling, authentication and error detection required to send information over a communications channel.
In HVAC a thin, reflective foil sheet that exhibits low radiant energy transmission and under certain conditions can block radiant heat transfer; installed in attics to reduce heat flow through a roof assembly into the living space.
Ceiling panels that contain electric resistance heating elements embedded within them to provide radiant heat to a room.
Energy that transmits away from its source in all directions.
A type of radiant heating system where the building floor contains channels or tubes through which hot fluids such as air or water are circulated. The whole floor is evenly heated. Thus, the room heats from the bottom up. Radiant floor heating eliminates the draft and dust problems associated with forced air heating systems.
Radiant heat transfer occurs when there is a large difference between the temperatures of two surfaces that are exposed to each other, but are not touching.
HVAC term for a heating system where heat is supplied (radiated) into a room by means of heated surfaces, such as electric resistance elements, hot water (hydronic) radiators, etc.
A room heat delivery (or exchanger) component of a hydronic (hot water or steam) heating system; hot water or steam is delivered to it by natural convection or by a pump from a boiler.
A device that releases pressure within a radiator when the pressure inside exceeds the operating limits of the vent.
Situation that occurs when the air being exhausted from a building is immediately brought back into the system through the air intake and other openings in the building envelope.
Air removed from the conditioned space and used for ventilation, heating, cooling, humidification, or dehumidification.
The compound (working fluid) used in air conditioners, heat pumps, and refrigerators to transfer heat into or out of an interior space. This fluid boils at a very low temperature enabling it to evaporate and absorb heat.
The process of the absorption of heat from one location and its transfer to another for rejection or recuperation.
A measure of the effective cooling capacity of a refrigerator, expressed in Btu per hour or in tons, where one (1) ton of capacity is equal to the heat required to melt 2,000 pounds of ice in 24 hours or 12,000 Btu per hour.
A measure of the percent of moisture actually in the air compared with what would be in it if it were fully saturated at that temperature. When the air is fully saturated, its relative humidity is 100 percent.
Air that is returned to a heating or cooling appliance from a heated or cooled space.
The central heating or cooling system contains a fan that gets its air supply through these ducts, which ideally should be installed in every room of the house. The air from a room will move towards the lower pressure of the return duct.
A measure of seasonal or annual efficiency of a central air conditioner or air conditioning heat pump. It takes into account the variations in temperature that can occur within a season and is the average number of Btu of cooling delivered for every watt-hour of electricity used by the heat pump over a cooling season.
Any device that receives a signal or stimulus (such as heat, pressure, light or motion etc.) and responds to it in a distinctive manner.
A thermostat that can be set to automatically lower temperatures in an unoccupied house and raise them again before the occupant returns.
A collection of computer programs, procedures and documentation that perform some tasks on a computer system.
The weight of water vapour, per unit weight of dry air.
HVAC term for an air conditioning system that comes in two to five pieces: one piece contains the compressor, condenser, and a fan; the others have an evaporator and a fan. The condenser, installed outside the house, connects to several evaporators, one in each room to be cooled, mounted inside the house. Each evaporator is individually controlled, allowing different rooms or zones to be cooled to varying degrees.
A term used to describe heat energy lost from a water heater tank.
Condition that exists when an equal amount of air is supplied to and exhausted from a space. At static pressure, equilibrium has been reached.
A water heater that releases hot water from the top of the tank when a hot water tap is opened. To replace that hot water, cold water enters the bottom of the tank to ensure a full tank.
HVAC term for the duct(s) of a forced air heating/cooling system through which heated or cooled air is supplied to rooms by the action of the fan of the central heating or cooling unit.
A water heater that heats water before it is directly distributed for end use as required; a demand water heater.
In HVAC individual rooms or zones in a building where temperature is controlled separately from other rooms or zones.
A unit of heat containing 100,000 British thermal units(BTU).
A unit of air cooling capacity; 12,000 Btu per hour.
A display which can detect the presence and location of a touch within the display area. The term generally refers to touch or contact to the display of the device by a finger or hand. Touchscreens can also sense other passive objects, such as a stylus.
A device, usually electrical, electronic, electro-mechanical, electromagnetic, photonic, or photovoltaic that converts one type of energy or physical attribute to another for various purposes including measurement or information transfer (for example, pressure sensors).
HVAC term for a fan-coil unit package device for applications in which the use of outdoor- and return-air mixing is intended to satisfy tempering requirements and ventilation needs.
A material that retards the movement of water vapour through a building element (walls, ceilings) and prevents insulation and structural wood from becoming damp and metals from corroding. Often applied to insulation batts or separately in the form of treated papers, plastic sheets, and metallic foils.
A HVAC system that has a stable supply-air temperature, and varies the air flow rate to meet the temperature requirements. Compared to CAV systems, these systems waste less energy through unnecessarily-high fan speeds. Most new commercial buildings have VAV systems.
A component of a heating or ventilation appliance used to conduct fresh air into, or waste air or combustion gases out of, an appliance or interior space.
HVAC term for a device mounted in the vent connector that closes the vent when the heating unit is not firing. This traps heat inside the heating system and house rather than letting it draft up and out the vent system.
A tube in which combustion gases from a combustion appliance are vented out of the appliance to the outdoors.
A type of combustion heating appliance in which the combustion gases are vented to the outside, either with a fan (forced) or by natural convection.
The process of moving air (changing) into and out of an interior space either by natural or mechanically induced (forced) means.
Defined as the total air, which is a combination of the air brought inside from outdoors and the air that is being re-circulated within the building. Sometimes, however, used in reference only to the air brought into the system from the outdoors; this document defines this air as "outdoor air ventilation."
The rate at which indoor air enters and leaves a building. Expressed in one of two ways: the number of changes of outdoor air per unit of time (air changes per hour, or "ach") or the rate at which a volume of outdoor air enters per unit of time (cubic feet per minute, or "cfm").
In HVAC caulking and weather-stripping to reduce air infiltration and exfiltration into/out of a building.
A material used to seal gaps around windows and exterior doors.
In HVAC an area within the interior space of a building, such as an individual room(s), to be cooled, heated, or ventilated. A zone has its own thermostat to control the flow of conditioned air into the space.
The combining of rooms in a structure according to similar heating and cooling patterns. Zoning requires using more than one thermostat to control heating, cooling, and ventilation equipment.
This website uses cookies to improve user experience. By using our website you consent to all cookies in accordance with our Privacy Policy.